A crew member climbs a trailer to tarp a load.
No guardrail, no anchor point, just a wet deck and a long drop. It's one of the most common ways drivers and yard crews get seriously hurt, and it happens on routine jobs, not rare ones.
For fleet safety & operations leaders
Prevent falls.
Protect uptime.
Engineered fall-protection systems that fit the trailers and trucks you already run. Built to deploy fast, hold up in the field, and keep your crew off the ground without slowing the job down.
Book a Meeting
15 minutes. We'll map a system to your fleet.
Where fleets take on risk
One fall changes everything. Same result: cost you didn't plan for.
OSHA shows up after the incident, not before.
Fall protection citations are expensive, and a documented injury on a job site brings scrutiny to every other truck and yard you operate. Compliance on paper isn't the same as compliance on the deck.
The truck sits while everyone figures out what to do.
An incident doesn't just cost the claim. It costs the load, the route, and the trust of the customer waiting on it. Prevention is cheaper than every version of the alternative.
Our approach
Fall protection built around how your operation actually runs.
Every fleet is different. Trailer types, dock heights, load patterns, and crew workflows all shape what a system needs to do. We start with your operation, not a catalog page.
- Deploys in seconds, not minutes, so it actually gets used
- Fits your existing trailers and trucks, no fleet retrofit required
- Rated for daily use in real weather, real routes, real crews
- Documented and built to support your OSHA 1910.29 compliance program
Built for your operation
Four ways to keep crews protected, chosen by how you load and move freight.
Permanent fall protection mounted directly to the trailer, ready every time it's loaded, no separate equipment to track down.
Portable protection that moves between trailers and job sites, built for yards running mixed equipment.
Fixed guarding for elevated work around equipment and loading areas, engineered to your facility's layout.
Non-standard trailers, tight clearances, or unusual dock heights. If it doesn't fit a catalog system, we engineer one that fits yours.
How we get you there
From walkthrough to installed system, without guesswork.
01
Assess
We look at your trailers, dock heights, and how crews actually work the load, in person or over a call.
02
Specify
We match a system, or a combination of systems, to your equipment and your compliance requirements.
03
Install
Systems ship ready to mount, with install support so you're not learning fall protection on the fly.
04
Support
As your fleet or facility changes, we adjust the system with it instead of leaving you with something that no longer fits.
On the call
What actually happens in 15 minutes.
1
We look at your equipment.
Trailer types, dock heights, and where your crews are exposed right now.
2
We flag the highest-risk points.
Where a fall is most likely, and what it would cost you if it happened tomorrow.
3
We map a system to your fleet.
What fits your equipment, your budget, and your timeline, starting with the highest-priority sites.
No obligation. No generic quote. Just a real read on your risk.
Questions we get a lot
Frequently asked questions
What is Truck Fall Prevention?
We design and build engineered fall-protection systems for trucking and industrial fleets, covering on-truck, mobile, machine guarding, and fully custom configurations.
Does this work with the trailers we already have?
In most cases, yes. Systems are built to fit existing trailer types and dock configurations. Non-standard equipment is handled through our custom systems process.
How long does installation take?
It depends on the system and fleet size. Most single-trailer installs are fast; fleet-wide rollouts are scheduled around your operational calendar so freight keeps moving.
Does this help with OSHA compliance?
Our systems are built to support fall-protection requirements under OSHA 1910.29. We'll walk through how a given system fits your compliance program on the call.
Can you handle multi-site fleets?
Yes. We work with single-yard operations up through multi-site fleets that need a consistent fall-protection standard across every location.
Last step
Get a real read on your fall risk. 15 minutes.
Tell us about your fleet and we'll show you where the exposure is, and what fixing it looks like.
Booking link coming soon — contact us directly in the meantime.
Book a Meeting